Welcome to visit us!

[email protected]

sae 4017 carbon steel material

SAE 4017 steel Steel grades0183;32;SAE 4017 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. Join GRADEAPPLICATIONY1Cr18Ni91Cr18Ni91Cr18Mn10Ni5Mo3N1Cr17Ni7See all 21 rows on www.steelgrades

Whatever your requirements about sae 4017 carbon steel material, you 'll find the perfect service-oriented solution to match your specific needs with our help. We are here for your questions anytime 24/7, welcome your consultation.

Online Chat [email protected]
  • Alloy Steel 4017 Forgings AISI 4017 All Metals & Forge

    General characteristics of Alloy Steel 4017 This steel is used as a surface hardening grade. It typifies a range of carbon content found in, say, a 4015 or 4020 type analysis. The molybdenum addition is for prevention of temper brittleness.

    Read More
  • Materials Medium Carbon Steel Bolts in SAE J429 (Grades

    Materials Medium Carbon Steel Bolts in SAE J429 (Grades 2, 5 and 8) Scope SAE J429 is the standard specification for inch series steel bolts, screws, studs, SEMS screws and U bolts in sizes up to and including 1 1/2 inches.

    Read More
  • AISI/SAE Steel Numbering System Engineering ToolBox

    AISI/SAE steel numbers are indicated below. Example AISI/SAE No. 1020. the first digit indicates that this is plain carbon steel. the second digit indicates there are no alloying elements; the last two digits indicates that the steel contains approximately 0.20 percent carbon ; Example AISI/SAE No. 4340

    Read More
  • AISI 1017 Carbon Steel (UNS G10170) Material Science

    AISI 1017 carbon steel is a medium low carbon steel, which has good welding property and slightly better machinability, compared to the lower carbon steels. It is soft and can be strengthened during cold working and drawing or forming. The following sections will discuss in detail about AISI 1017 carbon steel. Chemical Composition

    Read More
  • SAE/AISI Carbon & Alloy Steel Name System Otai Special Steel

    SAE steel 1018 indicates non modified carbon steel containing 0.18% of carbon. SAE steel 5130 indicates a chromium alloy steel containing 1% of chromium and 0.30% of carbon. An additional letter is sometimes added between the second and third digits of the

    Read More
  • Carbon Steel Grade 4037 Elgin Fasteners

    Do you need custom fasteners created with Carbon Steel Grade 4037? Since our inception, Elgin Fastener Group has met every challenge of providing Quality, Timely, Cost effective solutions for specialty fastener applications.

    Read More
  • SAE AISI 1527 (formerly 1027, G15270) Carbon Steel

    SAE AISI 1527 steel is a resulfurized carbon steel formulated for primary forming into wrought products. 1527 is the designation in both the SAE and AISI systems for this material. G15270 is the UNS number. Older literature may refer to this material as AISI 1027, but this is now discouraged.

    Read More
  • SAE AISI 1017 (G10170) Carbon Steel :MakeItFrom

    SAE AISI 1017 (G10170) Carbon Steel SAE AISI 1017 steel is a carbon (non alloy) steel formulated for primary forming into wrought products. 1017 is the designation in

    Read More
  • AISI 1010 Carbon Steel (UNS G10100) Materials

    Machinability (based on AISI 1212 steel as 100 machinability. The machinability of group I bar, rod, and wire products can be improved by cold drawing) 55 55 AISI 1010 carbon steel is mostly used in the annealed or case hardened condition. However, it can also be heat treated, quenched and tempered

    Read More
  • ASTM SAE AISI 1045 Carbon Steel Heat Treatment,

    SAE AISI 1045 Steel. ASTM SAE AISI 1045 steel is one of the commonly used medium carbon steels with an average carbon content of 0.45%, medium tensile properties, good strength, toughness and wear resistance. It can be treated by annealing, flame treatment or induction hardening.

    Read More
  • EN 1.4017 (X6CrNi17 1) Stainless Steel :MakeItFrom

    EN 1.4017 stainless steel is a ferritic stainless steel formulated for primary forming into wrought products. Cited properties are appropriate for the annealed condition. 1.4017 is the EN numeric designation for this material. X6CrNi17 1 is the EN chemical designation.

    Read More
  • AISI/SAE Steel Numbering System Engineering ToolBox

    AISI/SAE steel numbers are indicated below. Example AISI/SAE No. 1020. the first digit indicates that this is plain carbon steel. the second digit indicates there are no alloying elements; the last two digits indicates that the steel contains approximately 0.20 percent carbon ; Example AISI/SAE No. 4340

    Read More
  • High Strength Iso 4017 Carbon Steel Grade 10.9 Zinc Hex

    High Strength Iso 4017 Carbon Steel Grade 10.9 Zinc Hex Head Hollow Bolts , Find Complete Details about High Strength Iso 4017 Carbon Steel Grade 10.9 Zinc Hex Head Hollow Bolts,Bolt,Lock Tower Bolt,Hex Head Hollow Bolt from Bolts Supplier or Manufacturer Shanghai G & T Hardware

    Read More
  • SAE 1002 Carbon Steel USE®Fastener

    General Material:Stainless Steel,Nickel Alloy,Silicon Bronze,Aluminium Bronze,Brass,Naval Brass,Coppe,Copper Nickel,Aluminum Alloy,ium,Alloy Steel,Such as C1008

    Read More
  • SAE steel grades Quality Tools & Services, Inc.

    The prefix "C" denoted open hearth furnace, electric arc furnace or basic oxygen furnace, while "E" denotes electric arc furnace steel. Prior to 1995 the AISI was also involved, and the standard was designated the AISI/SAE steel grades. The AISI stopped being involved because it never wrote any of the specifications.

    Read More
  • Carbon steel

    Carbon steel is a steel with carbon content up to 2.1% by weight. The definition of carbon steel from the American Iron and Steel Institute (AISI) states. Steel is classified to be carbon steel whenno minimum content is specified or required for chromium, cobalt, molybdenum, nickel, niobium, titanium, tungsten, vanadium, zirconium, or any other element to be added to obtain a desired

    Read More
  • Carbon steel SAE 1010 [SubsTech]

    to Carbon steels to Properties of steels and cast irons carbon_steel_sae_1010.txt · Last modified2012/06/02 by dmitri_kopeliovich Except where otherwise noted, this work is licensed under a Creative Commons Attribution Noncommercial Share Alike 3.0 License

    Read More

What Can I Do For You?

Hot Products

Steel Materials

New Products

Copyright © 2015.BTN STEEL Co., ltd. All rights reserved.